Home > Error Code > Gpib Configuration Utility

Gpib Configuration Utility

Contents

If this error occurs, you must enable buffering and reopen the file. 1546 The VI must be in a project to use this property. 1548 Queue refnum cannot be obtained with Solution: Make sure the filename, path, and driver that you specified are correct. Check that the parameters entered are within the supported range for the hardware and drivers. 4804 Cannot write in file playback. It is also returned when a process tries to unlock an interface when no such lock exists.Solutions: The way to avoid the ELCK error is to wait for a random amount navigate here

Alternatively, system power may be disrupted for a variety of reasons or the actual instrument may begin to malfunction. Refer to the help for the property or method to determine if it is allowed remotely. 1033 Bad run-time menu file version. 1034 Bad run-time menu file. 1035 Operation is invalid One possible remedy for this is to update the firmware. The return type must be Void, Numeric, or String.

Gpib Configuration Utility

For legacy boards make sure that the jumpers and dip switches on the board are set to the same resource settings that the GPIB Configuration Utility thinks it is using. Ensure that a task is active and try again. The specific operating system error code for this condition is contained in ibcntl.

Set Segment Headers to One header per segment to correct this error. 1 An input parameter is invalid. For example, the network connection is down or a network cable is unplugged. 8 File permission error. Verify the values you wired to the Call Library Function Node. 1098 Cannot disconnect type definitions or polymorphic VIs if the block diagram is not available. 1100 No object of that Gpib Tutorial Establishing Communication With Your Instruments Once you have determined the GPIB address of your instruments, it is easy to establish communications to verify that you can send and receive data to

Figure 4. How To Find Gpib Address You also can use the Resource to Find field to query each instrument for an identification (ID) string. The paths must share a directory. http://digital.ni.com/public.nsf/allkb/463FA163E3B9FAA686256EFB00568691 The 0x08 flag is useful when running VIs with the Run VI method.

To correct this error, set the minimum size of the pane to a smaller value, or wire a value to the Splitter Position property that does not shrink the pane beyond Gpib Commands Check for loose or faulty cabling, and make sure that at least 2/3 of your instruments are powered-on (this is a requirement of the IEEE 488 specification). You must set the address of your instruments on their front panels or via DIP switches somewhere on the instruments. Install LabVIEW SignalExpress or visit www.ni.com/labview/signalexpress to download an evaluation version. −40601 The deterministic communication engine failed to initialize hardware. −4850 Device driver not present or not supported.

How To Find Gpib Address

Use the unit descriptor returned from ibdev or ibfind as the first parameter in subsequent NI-488 functions. The floating point data was outside of the range [-1.0, 1.0]. Gpib Configuration Utility This troubleshooting information is continued in Knowledge Base 1XOHEPPH: GPIB Error Codes and Common Solutions (Part 2)and Knowledge Base 3CO9NH3F GPIB Error Codes and Common Solutions (Part 3). Gpib Interactive Control This error might be caused by a failure to find or properly open the GPIB device driver. 1 Command requires GPIB Controller to be Controller-In-Charge.

The callback function is registered with the NI-488.2 driver when the ibnotify call is made. To correct this error, ensure the target VI is idle or reentrant. EDVR (0) ECIC (1) ENOL (2) EADR (3) EARG (4) ESAC (5) EABO (6) ENEB (7) EDMA (8) EOIP (10) ECAP (11) EFSO (12) EBUS (14) ESTB (15) ESRQ (16) ETAB Make sure that the access mode of the file is correct. Labview Error Code

To correct this error, remove either the 0x08 option or the 0x80 and 0x100 options. 1604 The Open VI Reference function does not support using the option 0x08 (Prepare for reentrant Cart|Help KnowledgeBase Request Supportfrom an engineer NIHome > Support > KnowledgeBase English 100 ratings: 3.27 out of 5   GPIB Error Codes and Common Solutions If your GPIB board is one of several controllers on the bus, then always check for the CIC bit of the status word, ibsta, before attempting any function calls that require For example, if you disabled hardware DMA by removing the DRQ/DACK jumpers on her legacy AT-GPIB/TNT, a call to ibconfigIbcDMA with a value of 1 to enable DMA would return this

This file cannot be saved until all dependent files have been named. 1022 Wizard Template not found. 1023 Wizard template does not have a diagram. 1024 Call Instrument aborted. 1025 Application Gpib-usb-hs Driver YourFeedback! Error on a WriteThe EABO (abort) status being returned from your GPIB write call (IBWRT function call) is the most common write problem.

Void can be used only as return type of function. 1186 Cannot show or hide the label on its own.

If your instrument is an older, non-IEEE 488.2 compliant device, then it will not understand "*IDN?", so it will not generate a message string for you to read from the instrument. YourFeedback! Ensure that the parameters values are within the supported range for the hardware and drivers. −4406 A VI item in the palette data array is not supported in this version of What Is Gpib The operation is not allowed on this kind of control or a control at this level. 1087 There is no DataSocket information available for the object. 1088 Bad value for parameter.

Avoid calling ibgts, except immediately after an ibcmd call. The system returned: (22) Invalid argument The remote host or network may be down. You cannot use this property with a Conditional Disable structure because conditions determine the active frame. Related Links: KnowledgeBase 2368N85R: ENEB Error (Non-existent GPIB Board Error) During Communication with InstrumentProduct Manuals: NI-488.2 User Manual for WindowsGPIB Support: Introduction to the Interactive Control (IBIC)Knowledge Base 1XOHEPPH:GPIB Error Codes

Repeat this process to confirm communication with all of your connected instruments. Make sure that the GPIB board is addressed correctly before calling ibrd, ibwrt, RcvRespMsg, or SendDataBytes. If EOS is the termination method, then be sure to append the termination character to the end of your message. Figure 3.