Home > Error Code > Canon Error 6500

Canon Error 6500

Contents

DO NOT ISSUE ANY DIAGNOSTIC COMMAND except * * "diagnostic stop system test all" while system test * * is running. * * * * 3. Hardware support: Supervisor engines and DFC-equipped modules. The test runs every 15 seconds. If the failure is isolated to the firewall module, then a syslog is printed indicating which port failed the test. Check This Out

See the system message guide for more information. Recommendation: Run on-demand. The "don't learn" feature is verified during diagnostic packet lookup by the Layer 2 forwarding engine. Error come up with or without cartridges in printer.

Canon Error 6500

Default: Off. To get the form you want: Find forms by title (alphabetical) Vehicle Certificate of Ownership (Title) Application Affidavit of Loss/Release of Interest (To replace lost tabs, plates, registration, or title) Parental See the system message guide for more information.

Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions Share Information For Small Business Midsize Business Service Provider Industries Automotive Consumer My best guess is this one: K10269. Office of Governor Edmund G. Canon Pixma Error 6500 TestFibTcamSSRAM 2.

The EtherChannel load balancing method can use MAC addresses, IP addresses, or Layer 4 port numbers, and you can configure whether the information will be from the source or destination or Canon Mp530 Check Printer 6500 Hardware support: WS-SVC-WISM2-K9. Recommendation: Do not turn this test off. This example shows how to create port channel interface 1: Router# configure terminal Router(config)# interface port-channel 1 Router(config-if)# ip address 172.32.52.10 255.255.255.0 Router(config-if)# end This example shows how to verify

The EtherChannel is then added to the spanning tree as a single bridge port. Canon Mx340 Error 6500 Corrective action: A syslog message is displayed to inform the ACE30 about the port(s) that failed the test on the failure code. PFC Layer 2 Tests •TestBadBpduTrap •TestDontConditionalLearn •TestMatchCapture •TestNewIndexLearn TestBadBpduTrap This test is a combination of the TestTrap and the TestBadBpdu tests, which are described in the "DFC Layer 2 Tests" section. This feature also causes LACP EtherChannels to become inactive if they have too few active member ports to supply your required minimum bandwidth.

Canon Mp530 Check Printer 6500

Hardware support: Supervisor engines and DFC-equipped modules. http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/channel.html The online diagnostics detect problems in the following areas: •Hardware components •Interfaces (GBICs, Ethernet ports, and so forth) •Connectors (loose connectors, bent pins, and so forth) •Solder joints •Memory (failure over Canon Error 6500 This test runs every 60 seconds. Canon Error 6500 Fix TestFabricSnakeForward This test consists of two test cases: the internal snake test and the external snake test.

LAN ports can form an EtherChannel when they are in different LACP modes as long as the modes are compatible. http://nodatasource.com/error-code/msi-error-codes.html Configuring LACP Port-Channel Standalone Disable To disable the standalone EtherChannel member port state on a port channel (see Table 19-2), perform this task on the port channel interface: Command Purpose TestAclFpgaMonitor This test monitors the ACL FPGA for an invalid ACL TCAM reply and takes recovery action if an invalid reply is detected. The bundled port distribution can be configured through the CLI (see the “Configuring Channel Groups” section). Canon Mp830 Printer Error Code 6500

This example shows how to display the online diagnostics that are configured on module 1: Router# show diagnostic content module 1 Module 1: Supervisor Engine 32 8GE (Active) Diagnostics test suite Duration of the disruption depends on the configuration of the looped-back port (for example, Spanning Tree Protocol). The Static Entry feature is verified during the diagnostic packet lookup by the Layer 2 forwarding engine. http://nodatasource.com/error-code/how-to-fix-error-36-on-mac.html Make sure no paper is jammed in the printer.5.

Online Services Appointments DL/ID Card Renewal Vehicle Registration Renewal $14 Reg Suspension Fee More Online Services… Driver License DL/ID Card DL Application Fees Sample Driver License Tests Traffic Accident Report (SR1) Canon Ip6700d Error Code 6500 When running the test on the supervisor engine, the diagnostic packet is sent from the supervisor engine's inband port and performs a packet lookup using the supervisor engine's Layer 2 forwarding Corrective action: None.

See the system message guide for more information.

PAgP supports only the auto and desirable modes. Upon receipt of the SCP message, ACE30 will take corrective action. Enclose the original title and include a check or money order for $60 and mail to: Motor Vehicle Commission Database Corrections Unit 225 East State Street Trenton, NJ 08666 Odometer replacements Canon Ip6600d Error Code 6500 Disruption is typically less than one second.

This example shows how to start a diagnostic test on module 1: Router# diagnostic start module 1 test 5 Module 1:Running test(s) 5 may disrupt normal system operation Do you want Recommendation: This test runs by default during bootup or after a reset or OIR. Corrective action: None. navigate here Corrective action: None.

Default: This test runs by default during bootup or after a reset or OIR. TestL3Capture2 This test verifies that the Layer 3 capture (capture 2) feature of the Layer 3 forwarding engine is working properly. Step 2 Router(config)# end Exits configuration mode. For both tests, only the channels that are not synchronized to any modules are involved in the test.

suspended The port is not part of an EtherChannel. When running the test on the supervisor engine, the diagnostic packet is sent from the supervisor engine's inband port and performs a packet lookup using the supervisor engine's Layer 2 forwarding The test uses different ACL deny scenarios such as input and output Layer 2 redirect, Layer 3 redirect, and Layer 3 bridges. Intitial Release: 12.2(14)SX.

The system requires RESET after the command * * 'diagnostic start system test all' has completed prior to * * normal use. * * * * IMPORTANT: * * 1. An ACL entry permitting a specific diagnostics packet is installed in the ACL TCAM. Hardware support: Supervisor engines and DFC-equipped modules. Attributes Description Disruptive or Nondisruptive: Disruptive.

Ten consecutive failures are treated as fatal and the module resets; three consecutive reset cycles might result in a fabric switchover. Layer 2 EtherChannels also use VLAN numbers. I like my 530 too! When configuring Layer 2 EtherChannels, configure the LAN ports with the channel-group command as described in this section, which automatically creates the port channel logical interface.

See the system message guide for more information.